What actually breaks on a window?
Four things account for almost every repair call. The glass itself cracks or chips. The sealed unit fogs because its perimeter seal has failed. The hardware gives out, which means balances, hinges, sash locks, pivots or rollers. Or the frame moves, and a window that used to slide square starts binding against the jamb. The distinction matters because only one of those four is a glass job. If you replace the pane on a window with a failed balance, the same window will be back on the list within weeks. A repair visit therefore starts by working out which of the four is actually happening, and only then talking about parts.
Why does fog appear between the panes?
Fog between the panes is not condensation on the inside of your house, and it cannot be wiped away. A double-pane unit is a sealed sandwich with a desiccant spacer holding the two panes apart. Once that perimeter seal fails, outside air carrying moisture gets into the cavity, the desiccant saturates, and the moisture condenses on the colder pane. From that point the unit is finished; the haze will spread and the window loses most of the insulating value it was bought for. No drilling, venting or cleaning kit restores it, whatever the adverts claim. The fix is a new sealed unit re-glazed into the existing frame, provided the frame itself is still sound.
Which repairs are still worth doing on older frames?
On a solid frame, almost all of them. A 1960s aluminium slider with flat rollers is a repair, not a replacement, because the extrusion is still straight and the track is still true. Replacing rollers, cleaning and re-setting the track and replacing the sash lock restores a slider that has been dragged for a decade. The same is true of a wood sash with a snapped cord or chain: re-cording is routine work. The line is drawn where the frame has gone soft at the sill, pulled away from the stucco, or visibly bowed. Patching glass into a frame that has lost its shape puts money into an opening that will keep leaking, and that is the point at which replacement is the honest answer.
What does a repair visit involve?
The visit establishes the cause first: which component failed and whether the frame is still square and dry. That is usually ten to fifteen minutes per opening. From there the job is either a parts repair done on the spot, a re-glaze requiring a measured sealed unit to be ordered, or a recommendation that the unit is past repair. You get the cause, the options and a written figure, and nothing is ordered without your go-ahead. Where a sealed unit has to be ordered, the window is made weather-tight before the technician leaves rather than left open to the marine air.
Get a written figure for this job
Repair is priced from the failed component and the state of the frame, so the figure only makes sense after the opening has been looked at. Tell us which window is misbehaving and what it has started doing, and the visit is arranged around that.
How do you tell a failed balance from a failed sash?
A window that will not stay up is usually a balance problem, and a window that will not close flush is usually a sash or hinge problem. On a single-hung or double-hung unit, the spiral or block-and-tackle balance carries the sash weight; when it snaps, the sash drops or jams at an angle and the frame starts to rack. You can usually hear the difference: a balance failure is silent and sudden, while a hinge or pivot failure grinds before it lets go. On a casement, a worn hinge causes the sash to sag so the lock no longer meets its keeper, which owners often mistake for a broken lock. Replacing the lock leaves the sash still sagging. Diagnosing which component has actually failed is the whole job on these calls.
What makes a repair fail a second time?
Three repeat failures account for most callbacks. A sealed unit ordered against a nominal size rather than the measured opening will not seat, and the gap is sealed with caulk that fails within a season. A sash re-glazed without checking the frame for square leaves the new unit stressed, and it cracks at a corner. A slider given new rollers without cleaning and re-setting the track destroys the new rollers within months, because the debris that wore out the first set is still in the channel. Each of those is avoidable by doing the diagnostic step first. A repair that fails twice costs more than the replacement it was meant to avoid, which is why the visit measures and inspects rather than simply quoting parts.
What can be done about a window that will not lock?
A window that will not lock is usually a symptom rather than a fault in the lock itself. On a casement, the sash has sagged on worn hinges so the lock tongue rides above or below the keeper, and the handle feels like it is jammed when it is simply misaligned. On a slider, a worn roller has dropped the panel so the latch misses its strike. On a double-hung, a stretched or snapped balance lets the upper sash sit low enough that the meeting rails never line up. In each case the mechanism is doing what it can against a sash that has moved. The repair is to restore the sash to its correct position, then adjust the keeper or strike to meet it. A new lock fitted to a sagging sash will feel tight for a week and then fail in exactly the same way, which is why the lock is the last thing checked rather than the first.
Common questions
Is it worth repairing a window instead of replacing it?
On a frame that is square and dry, yes, almost every time. A new sealed unit or a set of rollers costs far less than a new window and keeps the original opening, trim and stucco untouched. Replacement becomes the better answer when the frame has rotted at the sill, bowed, or pulled away from the wall.
Can fogged glass be cleaned rather than replaced?
No. Once the perimeter seal fails and moisture reaches the cavity between the panes, the desiccant saturates and the haze is permanent. Drilling or venting the unit does not clear it. The only real repair is a new sealed unit glazed into the existing frame.
Will you repair a window you did not install?
Yes. Repair work is assessed on what is actually there, not on who fitted it. The visit identifies the failed component and whether the frame is worth keeping, and the written figure follows from that.
What if the repair turns out to be a replacement?
You are told on site, with the reason, before anything is ordered. Nobody arrives at a repair and leaves with a replacement contract they did not ask about. The written figure for replacement is offered as an option, not as an upgrade.